Installing a new sink is an uncomplicated and quick task. The process is relatively easy, and you can do the installation part by yourself with a bit of experience. Then how to install faucets? Though some complicated kitchen faucets require professional installation, many of the kitchen fixtures can be installed easily.
Here is a guide on how to install faucets and sinks.
Materials Needed
In order to install the kitchen faucet and sink set, you will need the following list of things:
a sink, a faucet or tap, a basin wrench, a strainer set, pump pliers, a screwdriver, a crescent wrench, a spatula, plumber’s putty, silicone sealant, a bucket, a flashlight, and a set of towels.
How to install faucets, and this reason is nearby if you wish to enlarge the opening within the countertop. It is also necessary to know how to clean bathroom sinks to maintain hygiene.
Step By Step Guide To Install Faucets And Sinks
If you are looking for durable, sturdy, and premium quality faucets, it is best to choose Oltsw taps.
Here, we have mentioned the steps to know how to install faucets and sinks.
Step 1: Measure and mark the layout of the kitchen’s sink
Place the counter’s back edge in the center of the sink within its cabinet. If the sink contains a template, align it along the mark on the counter. This is the first step of how to install faucets. Place the back edge one and a half inches parallel to the counter. Trace around it; proceed to the subsequent degree.
If there is no template, use 2-inch tape to stipulate the sink location. Mark the middle of the sink on its back edge. Lay the sink inverted on the counter. Align the mark on the sink and the one on the counter together.
Step 2: Mark the cut lines on the counter
The cut line marking is the second phase of how to install faucets. The employing a straightedge to attach the marks, you will find yourself with an oblong outline on the counter of the sink’s hole. To approximate the radius of the corner of the sink, round off the corners by hand.
Take a slightly wider bit than the jigsaw blade (½-inch bit is typically enough). Then, at each junction of the cut-out lines, make sure to drill a hole inside the radius.
Step 3: Use a jigsaw to cut the sink opening
Place a jigsaw blade into a front hole and cut along the marked line to the back hole. Repeat on the opposite side. Lay a scrap of wood some inches longer than the cut-out across the sink area. Screw through the piece and into the cut-out waste to stop it from binding the saw blade or falling.
Cut along the cut lines marked at the front and back and remove the cut-out piece. Make sure that the fit of the sink in the countertop is set. If it is necessary, trim the opening with the jigsaw.
Step 4: Install the kitchen faucet
Set the sink the wrong way up on a padded sawhorse or counter. Then, feed the tap’s supply tubing and tailpiece through the gasket, which helps seal the faucet to the sink. Screw the washers and mount them on the lower side sink deck. This is the pre-final step of how to install faucets.
Just make sure that the tap can swing for a whole area across the sink deck before tightening mounting nuts.
Step 5: Attach The Strainer Over Applied Putty
Put the sink up, apply a thick roll of the plumber putty under the strainer edge, and push it up through the sink’s drain hole. Slip the housing (if your strainer has one), gasket, and washer onto the filter and against the lower side of the sink. Dab the pipe-joint compound and expose the opening threads.
Thread the locknut onto the strainer by hand, then tighten it with pliers while holding the filter in situ. Fit the gasket onto the tailpiece of the sink drain and attach it to the strainer through its slip nut. Tighten the nut using a hand while holding the filter.
Step 6: Set the sink and connect the water supply
Remove the tape, and pull it toward the center of the hole. With the sink still, the wrong way up, press a bead of silicone tapping around the lower side of the sink’s brim. Turn the sink upright and set it on the hole of the countertop.
Make sure that the front of the sink is parallel with the front fringe of the countertop. Adjust it, if necessary. Next, use the corn-head supply tubes or the braided stainless-steel hoses to connect the tap and shut off the valves. Now, attach the required sprayer hose to the faucet’s threaded tailpiece.
Step 7: Connect The Drain Pipes
Assemble the trap adapter on top of the sink-drain tailpiece. Cut and dry-fit the length of the PVC pipe and attach the trap adapter to the trap and the drain elbow to the waste line. Then slide the web on the tailpiece to finely tune the length and alignment of the pipe.
Take the drain pieces apart. Clean the cut ends with a utility knife. Use a PVC primer to coat it and its mating pieces. Let it dry and hold for 30 seconds. Now you are finishing the process of how to install faucets.
Conclusion
The essential features of kitchens and bathrooms are the sink and faucets. The sink and faucets need to be installed properly to avoid any damage and issues later on. Taking this into account, we have mentioned how to install faucets with significant steps to be followed while installing sinks and kitchen faucets.
Additional reading:
- Small Kitchen Storage Ideas
- Know About The Type Of Kitchens According To Different Size
- Different Types of Conversions to Make the Most of Spare space
